ML2010 Knight Electronics Workstation

Features:

Power Input:

• 120 Volt AC 50/60 Hz
• Fused (2A 250V, 5x20mm Glass, Fast Acting)
• Lighted Power ON Indicator

DC Power Sources:

• +5 Volts ±3% @ 1 AMP
• -5 Volts ±3% @ 1 AMP
• +12 Volts ±3% @ 1 AMP
• -12 Volts ±3% @ 1 AMP
• 0 to >+18 Volts Variable @ 1 AMP
• 0 to >-18 Volts Variable @ 1 AMP (Isolated Ground for Variable Supplies)
• 0.1% Line Regulation
• 0.1% Load Regulation
• Short Circuit and Thermal Overload Protected

AC Power Source:

• 15 Volts Center Tapped @ 500 Milliamps

Pulse Generator:

• Continuously Variable in Five Decade Ranges: Pulse Width: ≤ 100nSEC to ≥10mSEC; Pulse Repetition: ≤ 1uSEC to ≥ 100mSEC
• Overlap Indicator
• Capable of 100% Duty Cycle
• Pulse Position and Width Modulation Inputs
• TTL Compatible Gate and Trigger Inputs
• Rise and Fall Times Less than 10nSEC

Sweep Ramp Generator:

• Adjustable Period: ≤ 1mSEC to ≥ 1SEC
• Adjustable 0 to 3.7 Volt Output Amplitude
• Negative Linear Ramp Output for Linear Sweep
• Separate TTL Compatible Sync Output

Function Generator:

• Sine, Square, or Triangle Wave Output
• 0 to 18 VPP Output Amplitude
• ~500 Ω Output Impedance
• Short Circuit Protected
• DC Offset Adjustable from 0 to ±10 Volts
• Separate TTL/HC Compatible Clock Output: (20mA Output at 0.33VDC (Low) or 4.3VDC (High)
• Rise/Fall Time Less Than 20nSEC
• Continuously Variable Frequency From 1Hz to 1MHz in six decade ranges (Note: Due to limitations of the function generator chip waveform variations, or roll off, may be experienced at the maximum range.) 
• Distortion: Sine Wave ≤ 2% to ≥ 100kHz
• Triangle Wave ≤ 2% to ≥ 100kHz
• Rise & Fall: Square Wave ≤ 20nSEC
• Frequency Modulation Input
• Amplitude Modulation Input
• Burst Input
• Sweep Input Capable of 1000: 1 Sweep; (Start frequency determined by sweep ramp amplitude stop frequency determined by generator frequency setting)

Speaker:

• 2-1/4” 8Ω 0.25W

Potentiometers:

• Undedicated 1KΩ and 100KΩ
• Linear Taper
• 20% 0.125W

Indicators:

• Eight buffered LED (CMOS/TTL Compatible)

Switches:

• Eight Level - 0V or +5V Unbuffered toggle switches
• Two undedicated SPDT Toggle Switches [ON – NONE – ON]
• Two undedicated SPDT Momentary [ON – NONE – (ON)]

Pulsers:

• Two TTL Level debounced pulsers with complementary outputs

Interface:

• DB25 Male – DB9 Male – DB25 Female
• DB25 Female – DB9 Female – DB25 Female
• (DB25 to DB25 Pinned 1 to 1 with DB9 Common to first 9)
• Three BNC to TIE-Point Block

The ML2010 is a complete prototyping station and has been designed to consolidate all of your test equipment needs into one compact package.

This miniature laboratory used in conjunction with an oscilloscope and multimeter puts everything you need at your fingertips for building and testing all types of digital and analog circuits.

The features incorporated in this equipment are perfect for the hobbyist, designer, technician, and student in electronics.