N8482H Keysight Technologies RF Sensor

Features:

• EEPROM to store cal factors eliminates manual entry
• Wide frequency range from 100 kHz to 6 GHz
• Wide dynamic range from -15 dBm to +35 dBm
• Best-in-class power linearity of less than 1%, excellent SWR of mismatch uncertainty and highly accurate power repeatability
• Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)
• SCPI codes compatible with 8480 series (option CFT)

Note: Option CFT is available as a replacement of legacy 8480 Series power sensors intended for cal factor manual entry and SCPI compatibility. Option CFT is not compatible with 43x and other obsolete power meters.

• SCPI codes compatible with E-Series sensor (standard option)
• Compatible with EPM (N1913/14A, E4418/19B), EPM-P (E4416/17A), P-Series (N1911/12A) power meters

Note: All N8480 series power sensors are not compatible with the Keysight 43x, E1416A, N8262A power meters, 5314x microwave counters and E7495x base station test set.

N8480 Series Power Sensors are the replacement solutions for 8480 Series Power Sensors.

Thermocouple Power Sensor (100 kHz to 6 GHz)

The 8480 Series power sensor is well recognized as an industry standard for power measurements. It has been available to the industry for over 30 years and is widely used in design, manufacturing, or metrology applications for continuous wave (CW) or complex modulated signals.

Keysight is introducing the N8480 Series power sensors, a new thermocouple power sensors as a replacement for the 8480 Series power sensors (excluding the D-model sensors). It is enhanced with a few key features such as built-in EEPROM, extended dynamic range, wider frequency range, and - most important - better accuracy and repeatability.

N8480 Series Standard (N848x)

The N8480 Series power sensor incorporates the latest sensing technology, with value-added features such as the built-in EEPROM circuit, wider dynamic range and better linearity and accuracy.

Similar to the E-Series power sensors, the N8480 Series power sensors are designed with a built-in EEPROM to store the sensor characteristics such as model number, serial number, linearity, temperature compensation, calibration factors, and so forth. This feature ensures that this correction data will be loaded into the power meter when the sensor is moved from one power meter to another power meter. Therefore, it provides ease of use and convenience to you.

• Wider dynamic range: –35 dBm to +44 dBm (5 dB improvement from legacy 8480 Series)

• -5 dBm to +20 dBm (N8481/82/85/87A/86AQ/86AR/88A)
• 15 dBm to +35 dBm (N8481/82H)
• 5 dBm to +44 dBm (N8481/82B)

• Wider frequency coverage: 100 kHz to 67 GHz (sensor dependent)
• Excellent power linearity of less than 1%
• EEPROM feature to store cal factors
• Compatible with EPM, EPM-P, and P-Series power meters (only applicable when used with compatible firmware)

N8480 Series Option CFT (N848x-CFT)

The N848x-CFT behaves as the legacy 8480 Series sensors. You are required to enter the cal factor data manually for a particular frequency prior to make a measurement or enter the sensor cal factor table manually and select the frequency of signal to be measured.

• Dynamic Range: -30 dBm to +44 dBm (same as legacy 8480 Series)

• -30 dBm to +20 dBm (N8481/82/85/87A/86AQ/86AR-CFT)
• -10 dBm to +35 dBm (N8481/82H-CFT)
• 0 dBm to +44 dBm (N8481/82B-CFT)

• Backward compatible with 8480 Series SCPI codes
• EEPROM feature is disabled to maintain backward compatibility with 8480
• Excellent power linearity of less than 1%
• Compatible with EPM, EPM-P, and P-Series power meters and E7495A/B base station test set

Power meter compatibility

The N8480 Series power sensors operate with the Keysight EPM, EPM-P, and P-Series power meters and also the Base Station Test Set.